Skip to product information
1 of 5

Epoxy Shield

Rust-Oleum Epoxyshield Stain Additive for Premium Clear

Rust-Oleum Epoxyshield Stain Additive for Premium Clear

Regular price Rs. 3,825.00
Regular price Rs. 4,250.00 Sale price Rs. 3,825.00
Sale Sold out
Tax included. Shipping calculated at checkout.

EpoxyShield Stain Additive kit is designed to be mixed with the EpoxyShield 263997 Low VOC Premium Clear Floor Coating kit to create a high performance finish with a professional look. The Low VOC Premium Clear Floor Coating is a two-component epoxy coating designed to provide excellent wear, impact, and abrasion resistance to heavy foot and vehicle traffic. The Stain Additives are NOT stand alone coatings and must be mixed with EpoxyShield 263997 Low VOC Premium Clear Floor Coating kit.

For use in covered areas only. Not intended for carports or areas exposed to direct sunlight. Prolonged exposure to direct sunlight will cause the coating to fade with age. These changes are cosmetic in nature only, and the performance of the coating will not be affected.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Epoxyshield Stain Additive For Premium Clear

  • Creates a high performance finish with a premium professional look
  • 100% satisfaction guarantee
  • Kit includes stain, application tools, concrete etch, instruction sheet & DVD
  • Easy one coat system

How to Apply Epoxyshield Stain Additive For Premium Clear

Surface Preparation

For best results, clean 10x10 foot (3x3 meters) sections at a time. Completely wash, rinse, and squeegee each section before moving on to the next. When all the sections have been completed in this manner, then rerinse and squeegee the entire floor. When the floor is dry, rub your fingers on the concrete and check for a white film. If a white dust or powder is detected, then repeat the rinsing process being sure to thoroughly scrub during the rinse. Once the concrete is free of surface residue, you are ready to begin application of the coating. All pilot lights or open flames in the area must be extinguished due to the flammability of the solvents in the coating. Pilot lights or open flames must remain extinguished for a minimum of 24 hours following application of the EpoxyShield Premium Clear coating.

Previously Coated Floors : Make sure the floor is clean and dry. The EpoxyShield Low VOC Premium Clear coating is designed for use over the EpoxyShield Garage Floor finish or EpoxyShield Professional finish. The EpoxyShield Low VOC Premium Clear coating can be applied over the Garage Floor finish after 24 hours. The Low VOC Premium Clear coating can be applied over the Professional Floor finish between 16 hours and 5 days. For other previous coatings, use a wire brush to remove any loose or peeling paint or stain. If floor is sealed, the sealer will have to be removed by grinding or shot blasting. To ensure proper adhesion, scuff sand the entire surface.


Allow new concrete to cure for a minimum of 28 days. Check the garage floor for conditions that might interfere with proper adhesion (see directions sheet). Remove any oil spots or spills and wash the floor with EpoxyShield Heavy Duty Degreaser or a suitable detergent or degreasing solution. Thoroughly rinse with fresh water. Then etch the floor using Rust-Oleum Concrete Etch.

For best results when using the Concrete Etch, the concrete should be damp, but free of puddles. Mix the entire contents of the Concrete Etch granules with 2 gallons (3.79 liters) of water. Do not add Concrete Etch directly to paint. Use a plastic sprinkling can to evenly distribute the Concrete Etch solution. Scrub the floor with a stiff bristle brush and make sure the floor stays wet during this process until you are ready to rinse. Pay special attention to the area where the vehicle tires normally stand. Continue to scrub while rinsing to ensure all contaminates are washed away. Squeegee off excessive water or puddles and allow to dry.

Properties of Epoxyshield Stain Additive for Premium Clear - Kit

Brand Rust-Oleum EpoxyShield
Manufacturer Rust-Oleum
Resin Type Amine Cured epoxy
Pigment Type Varies with color
Solvents Methyl Acetate
Volatile Organic Compounds <50 g/l (0.42 lbs./gal.)
Mixing Ratio 8 ounces stain additive per 120 ounces of clear base
Practical Coverage 500 sq.ft./gal. (23 m2/l) on painted surfaces
250 sq.ft./gal. (46 m2/l) on bare concrete
Induction Period None
Pot Life @ 70-80°F (21-27°C) and
(21-27°C) 50% Relative Humidity
90 minutes
Dry Times at 70-80°
(21-27°C) and 50% RH
10 hours to Light Foot Traffic
24 hours to Heavy Foot Traffic
4 days Vehicle Traffic
Shelf Life 2 years
Flash Point 32°F (0°C
Safety Information For additional information, see MSDS
Technical Data Sheet Click here
View full details