Rust-Oleum NeverWet Liquid Repelling Treatment Spray Kit
Rust-Oleum NeverWet Liquid Repelling Treatment Spray Kit
Rust-Oleum NeverWet Liquid Repellent Spray is designed to repel water, mud, ice and other liquids. This multi-surface treatment creates moisture repelling barrier on numerous surfaces such as metal, wood, aluminum, galvanized metal, PVC, concrete, masonry, asphalt, vinyl siding, fiberglass, canvas, most plastics and more. This is ideal to use for interior and exterior surface.
NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.
Features of Never Wet Liquid Repellent
- Reduces damages which occurs due to rain. For an example, rust.
- Ultimate coverage up to 10 square feet.
- Dries in 30 minutes to touch.
- Patent pending 2-part spray system.
- Protects virtually any surface from corrosion and wear.
NOTE: Reapply top coat spray when liquid no longer rolls off. It is not recommended for electronic devices or clothing.
How to Video of NeverWet Liquid Liquid Repellent Spray Kit?
How to use Liquid Liquid Repellent Spray?
Appropriate Conditions to use
Use outdoors or in a well ventilated area such as an open garage. Use when temperature is between 50ºF (10ºC) and 90ºF (32ºC) and humidity is below 85% to ensure proper drying. Avoid spraying in very windy and dusty conditions. Cover surrounding area to protect from spray mist.Surface Preparation
Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Lightly sand glossy surfaces to create a surface profile.
Application/Spraying
Base Coat Application:Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact RustOleum. A test pattern on cardboard is recommended to obtain a feel for the spray pattern. Hold can upright 6-12” from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Continue to shake the can between passes. Keep the can the same distance from the surface. Keep the can in motion while spraying. Apply two or more base coats a few minutes apart. Allow to dry for at least 30 minutes before applying the topcoat. Do not use near open flame.
Top Coat Application:Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. A test pattern on cardboard is recommended to obtain a feel for the spray pattern. Hold can upright 6-12” from surface and spray in one steady pass. Avoid soaking the surface. Stop and wait for each pass to dry for 1-2 minutes. Three or four coats will give optimum results. Do not apply any other topcoat other than NeverWet as it will lose its moisture repellent properties.
Properties of NeverWet Liquid Repellent Spray Kit
Base Coat | Top Coat | |
---|---|---|
Resin Type | Hydrocarbon | NA |
Pigment Type | NA | NA |
Fill Weight | 255 Grams | 255 Grams |
Practical Coverage at Recommended DFT (assumes 15% material loss) |
10 sq.ft./can | 10 sq.ft./can |
Dry Times at 70-80ºF (25-27ºC) and 50% Relative Humidity |
15 minutes to touch and 15 minutes to re-coat (with itself) |
30 minutes to touch and 1 minute to re-coat (with itself) |
Dry Heat Resistance | 230°F (110°C) | 230°F (110°C) |
Shelf Life | 4 Years | 4 Years |
Flash Point | 156°F (-104°C) | 156°F (-104°C) |
Safety Information | For additional information, see SDS | |
For Technical Data Sheet | Click here |