248914 248914 Automotive

Rust-Oleum Automotive Truck Bed Coating Spray

Product Code: 248914

Availability:Out of stock

Rust-Oleum Automotive Truck Bed Coating Spray offers durability, abrasion resistant, textured, non-skid finish to truck beds. This aerosol spray reduces road noise and contours to the exact shape of the truck bed. It also provides protection from rust, scratch, weather and fading. Rust-Oleum Truck Bed Coating features an advanced spray system that allows you to spray at any angle, even upside down for those hard to reach areas. A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Truck Bed Coating Spray

  • Creates non-skid surface.
  • Made with Rust-Oleum Stops Rust formula.
  • Ideal for truck beds, fenders, steps, trailer, floors etc.
  • Protection from scratches, weather and fading.
  • Convenient any-angle spray and comfort tip.

NOTE: This coating is not ideal to use for hot surfaces.

Featured Video of Rust-Oleum Automotive Truck Bed Coating Spray

How to Apply Truck Bed Coating Spray

Environmental Conditions for Spraying

Use outdoors or in a well ventilated area such as an open garage. Use when temperature is between 50-90°F (10- 32°C) and humidity is below 85% to ensure proper drying. Avoid spraying in very windy and dusty conditions. Cover surrounding area to protect from spray mist.

Surface Preparation

Bare Metal or Sound Rust Surfaces: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or 120-220 grit sandpaper. Remove all sanding dust with a clean cloth. Protect and mask off all surrounding areas to prevent overspray. For best results, spot prime bare or rusted surfaces.

Previously Painted Surfaces: Thoroughly clean the area with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Note: Cleaning is recommended before and after wire brushing or sanding. Use a wire brush to remove any loose or peeling paint. Sand the surface with 120-220 grit sandpaper. The use of Primer Sealer Spray or any of the sandable primers (249419 Red, 252472 Light Gray, or 249415 Gray) will enhance corrosion resistance and improve hiding.


Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 10-12" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can in motion while spraying. Remove any overspray from the auto finish immediately. For best results, apply 2 coats, allowing 1-2 minutes between coats. Do not use near open flame.

Properties of Rust-Oleum Automotive Truck Bed Coating Spray

Brand Rust-Oleum
Weight 425 Grams
Recommended Dry Film
Thickness (DFT) per Coat
1.0-1.5 mils (25-37.5µ)
Practical Coverage at Recommended
DFT (assumes 15% material loss)
15-20 sq. ft./can
Dry Times at 70-80F
(21-27°C) and 50% Relative Humidity
1 hour to touch and
re-coat within an hour or after 24 hours
Resin Type Alkyd
Pigment Type Varies with color
Solvents Aromatics hydrocarbons and Ketones
MIR 1.20 Max
Dry Heat Resistance 200°F (93°C)
Flash Point -156°F (-104°C)
Shelf Life 5 Years
Safety Information For additional information, see MSDS
Technical Data Sheet Click here