Rust-Oleum Zinsser Bulls Eye 1-2-3 -  Spray

Rust-Oleum Zinsser Bulls Eye 1-2-3 - Spray

Regular price Rs. 520.00 Sale

Zinsser Bulls-Eye 1-2-3 is a high hide water-based styrenated acrylic water-based primer-sealer stain blocker and bond coat designed for priming all surfaces. Apply to interior and exterior walls, ceilings, doors, trim, fascia, soffits, foundations, railings, and related paintable surfaces. Bulls-Eye 1-2-3 bonds to wood, plaster, concrete, gloss enamels, hardboard, glass and tile. It provides a rust inhibitive coating on iron railings, steel frames, piping, etc. It resists the growth of mold and mildew in damp, humid environments. It resists high pH surfaces (up to 12.5) and seals most porous surfaces. Bulls-Eye 1-2-3 traps most stains in the primer film including graffiti, grease, rust, cedar and redwood tannin, creosote, and asphalt stains

Features of Zinsser Bulls Eye 1-2-3 Spray


  • Designed for interior and exterior surfaces
  • Bonds to glossy surfaces without scuff sanding
  • Formulated with stain-blocking resins
  • Rust inhibitive – may be used to prime ferrous metal
  • Is mold and mildew resistant
  • Fast drying – Recoat in under 1 hour
  • Sticks to all surfaces and sands easily
  • Excellent for sealing water soluble tannin bleed on cedar and redwood
  • Easy soap and water clean-up
  • High hiding formula blocks most stains
  • How to Apply Zinsser Bulls Eye 1-2-3 Spray


    Surface Preparation


    Surfaces should be clean, dry, sound and free of dust, dirt, excessive chalky material, grime, grease, oil, wax, mildew, wallpaper, adhesive or any contamination that may interfere with adhesion. If unsure of cleanliness, always wash surface with an appropriate ammoniated cleaning solution or solvent (do not use TSP as a cleaner). Remove any peeling and/or unsound coatings. Sand any remaining paint film edges smooth with the surface. Lightly sand exposed exterior wood with 80 to 100 grit sandpaper to remove loose or weathered wood fibers and mill glaze.


    When priming over stained areas, first attempt to remove as much of the stain as possible by washing, sanding, scraping, etc. Bare wood that has been exposed for more than 4 weeks should be lightly sanded or abraded to remove weathered wood fibers. Remove exterior mold & mildew with Zinsser Jomax Mildew Killer and House Cleaner. Remove interior mold and before painting with a solution of one cup household bleach per gallon of water or a quality mildew cleaner. Rinse well and allow surface to dry completely before priming. Countersink exposed nail heads, spot prime and fill all nail holes and gouges with Zinsser Ready Patch spackling compound. Wire brush rusty areas. Spot prime knots and sap streaks with B-I-N Primer-Sealer before whole surface priming with Bulls-Eye 1-2-3.


    Application


    Apply only when air, material, and surface temperatures are between 50-90ºF (10-32ºC) and the surface temperature is at least 5ºF (3ºC) above the dew point. The relative humidity should not be greater than 85%


    Aerosol - - Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 10-16” from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying. Apply two or more light coats a few minutes apart to avoid drips and runs. Do not use near open flame.

    Properties of Rust-Oleum Zinsser Bulls Eye 1-2-3 Spray


    Brand Rust-Oleum Zinsser
    Manufacturer Rust-Oleum
    Resin Type Styrene Acrylate Copolymer
    Pigment Type Titanium Dioxide
    MIR 1.2 Max
    Solvents Acetone, Aliphatic Hydrocarbons
    Weight 368 gr.
    Volatile Organic Compounds NA
    Recommended Dry Film
    Thickness (DFT) per Coat
    1.5-2.5 mils
    (37.5-62.5µ)
    Practical Coverage at Recommended
    DFT (assume 15% material loss)
    10-12 sq.ft./can
    (0.9-1.1 m2)
    Wet Film to Achieve DFT
    (Unthinned material)
    NA
    Dry Times at 70-80°
    (21-27°C) and 50% RH
    30 minutes to Touch
    1 hour to Re-C0at
    2 hours, 24 hours over cedar to Stain Sealing
    7 days to Full Hardness
    Shelf Life 5 years
    Flame Spread (ASTM-84-97A) NA
    Smoke Contribution (ASTM-84-97A NA
    Flash Point -156°F (-104°C)
    Safety Information For additional information, see MSDS
    Technical Data Sheet Click here