200041H 200041H Varathane

Varathane Crystal Clear Water Based Polyurethane for Interior

Product Code: 200041H

Availability:Out of stock

Rs. 2,250.00 Rs. 2,025.00 2,025.00
Varathane Water Based Polyurethane is a crystal clear innovative coating which makes wooden surface scratch and stain proof. The quality which makes more convenient to use is fast drying. This is the polyurethane which get dried in an hour to touch and its 1 liter can treat 75-150 square feet of area. This is compatible to use for interior wooden project such as stained, bare, or painted etc. This crystal clear polyurethane is suitable for furniture, doors, windows, cabinets etc. Varathane Polyurethane provides a hard, crystal-clear finish that never yellows and lasts two times longer than traditional wood finishes.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Crystal Clear Water Based Polyurethane For Interior

  • Ideal for interior furniture, doors, cabinets and trim.
  • Delivers non-yellow finish.
  • Fast-drying, apply up to 3 coats/day.
  • Low odor and fast, easy soap-and-water clean-up.

NOTE: To obtain best result, 4 coats are suggested.

How to Apply Varathane Water-Based Polyurethane?

Surface Preparation

Previously Finished Surfaces  To ensure proper adhesion, surfaces must be clean, dry and free of wax, grease, oil, shellac, lacquer, mildew and polishes. Remove wax with a wax stripper, shellac with a paint stripper, and mildew with a solution of up to 10% household bleach and water. Old finishes in poor condition must be removed by sanding using 120-150 grit sandpaper. Sand to obtain a smooth surface. Do not use steel wool as rust may develop after the finish is applied. Remove all sanding dust using a vacuum or cloth dampened with mineral spirits.

Unfinished Surface Preparation - Sand smooth using 120-150 grit sandpaper and remove all sanding dust with a vacuum or cloth dampened with mineral spirits. If a filler or putty is used, make sure that it does not contain wax and allow enough time for it to dry thoroughly.

Stained Or Painted Wood - Follow manufacturer's directions for application of stain or paint. Make certain the surface is thoroughly dry before applying Varathane Crystal Clear Polyurethane. For best results, use Varathane Premium Wood Stains.


Brush Application - Stir thoroughly before and during use. To prevent bubbles, DO NOT SHAKE. Apply using a good quality, synthetic bristle brush, foam brush, or applicator. Allow the finish to dry a minimum of 2 hours and then re-coat. Lower temperatures and/or higher humidity may cause slower dry times. Re-coat only when previous coats have dried clear and feel hard (no longer tacky to touch). A powder should develop when lightly sanded. If any coat has dried more than 24 hours, lightly sand before re-coating to avoid brush marks. A minimum of 3 coats are recommended. If grain raise occurs, sand smooth before final coat. Allow finish to dry 24 hours before light use. Wait 3 days before subjecting surface to normal usage. Clean application tools and equipment with soap and water. Dispose of properly.

Properties of Varathane Crystal Clear Polyurethane

Brand Varathane
Manufacturer Rust-Oleum
Resin Type Acrylic Modified Urethane
Pigment Type Microcrystalline Silica
Solvents Glycol Ethers, Water
Weight 946 ml and 3.78 Ltr
Recommended Dry Film
Thickness (DFT) Per Coat
1.0-1.5 mils(25-37.5µ)
Practical Coverage
at Recommended DFT
230-350 sq.ft./gal.(5.7-8.6 m2/l)
Dry Times at 70-80°F(21-27°C)
and 50% Relative Humidity
30 minutes to touch. 2 hours to re-coat.
Light Use 24 hours.
Shelf Life 3 years
Flash Point 167°F (75°C)
Safety Information For additional information, see MSDS
Technical Data Sheet Click here