EpoxyShield Solvent-based Epoxy Premium Clear Coating is a two component, high solids epoxy coating. It is designed for application to bare concrete floors to provide excellent adhesion, durability, and chemical resistance. It can also be used as a clear finish over previously coated concrete floors. It is not intended for use outdoors or on unsound previous coatings or floors that have a moisture problem.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Epoxyshield Premium Clear Coating

Indoor use only
High-gloss
Chemical and water resistant

How to apply Epoxyshield Premium Clear Coating

Surface Preparation

Allow new concrete to cure for a minimum of 28 days. Remove any oil spots, grease or spills and wash the floor with EpoxyShield Heavy Duty Degreaser or a suitable detergent or degreasing solution. Thoroughly rinse with fresh water. Then etch the floor using Rust-Oleum Concrete Etch or Rust-Oleum 108 Clean & Etch. All pilot lights or open flames in the area must be extinguished due to the flammability of the solvents in the coating.

Previously Caoted Floors : This coating is designed for use over the EpoxyShield Garage Floor Finish or EpoxyShield Professional Finish. EpoxyShield Premium Clear Coating can be applied over the Garage Floor Finish after 24 hours. The EpoxyShield Premium Clear Coating can be applied over the Professional Floor Finish between 16 hours and 5 days. For other previous coatings, use a wire brush to remove any loose or peeling paint or stain. If floor is sealed, the sealer will have to be removed by grinding or shot blasting. To ensure proper adhesion, scuff sand the entire surface.

Application

Pilot lights or open flames must remain extinguished for a minimum of 24 hours following application of the EpoxyShield Premium Clear Coating. Apply only when air, material, and surface temperatures are between 60-85°F (15-29°C) and the surface temperature is at least 5°F (3°C) above the dew point. The relative humidity should not be greater than 85%. The minimum floor temperature for painting is 55°F (13°C).

Pour a portion of the admixed material into a lined paint pan. Immediately begin to cut in the perimeter of the floor along the wall, or other areas where a roller cannot reach, using a brush or edger before beginning roller application. Use a synthetic roller cover on a 9"" roller frame to apply an even coat of EpoxyShield Premium Clear Coating onto the surface. Limit the application to 4x4 foot (1.2x1.2m) sections at a time. Maintain a wet edge to prevent lap marks and gloss variations. Make all final passes in the same direction to ensure uniform appearance. If using the anti-slip additive, continue to stir the admixed material periodically to ensure additive does not settle in the pan. Only one coat is necessary under most circumstances. EpoxyShield Premium Clear must be used within 90 minutes following initial mixing to ensure even gloss.

Properties of EpoxyShield Premium Clear Coating - kit

Brand	Rust-Oleum EpoxyShield
Manufacturer	Rust-Oleum
Resin Type	Amine Cured Epoxy
Pigment Type	None
Solvents	Oxsol 100, Methyl Acetate
Volatile Organic Compounds	<100 g="" l="" 0="" 83="" lbs="" gal="" td="">
Mixing Ratio	2:1 Base to Activator by volume
Practical Coverage	500 sq.ft./gal. (23 m2/l) on painted surfaces 250 sq.ft./gal. (46 m2/l) on bare concrete
Induction Period	None
Pot Life @ 70-80°F (21-27°C) and (21-27°C) 50% Relative Humidity	90 minutes
Dry Times at 70-80° (21-27°C) and 50% RH	10 hours to Light Foot Traffic 24 hours to Heavy Foot Traffic 4 days Vehicle Traffic
Shelf Life	5 years
Flash Point	Base Component: 31°F (-1°C) Activator Component: 234°F (112°C)
Safety Information	For additional information, see MSDS
Technical Data Sheet	Click here

Rust-Oleum EpoxyShield Premium Clear Coating - 1 Kit

Have a question?