288339 288339 Wolman

Rust-Oleum Wolman Water-Based RainCoat One Coat Clear Sealer - Satin

Product Code: 288339

Availability:Out of stock

Rs. 4,680.00 Rs. 4,210.00 4,210.00

Wolman Raincoat One Coat Clear Sealer is a clear water-based exterior water repellant designed to provide protection against water damage and mildew. Raincoat® One Coat Clear Sealer formula is colorless which allows the wood’s original color and grain to show through while protecting the surface from water damage.

The NeverWet hydrophobic technology properties and superior water repellency helps maximize resistance to wood cracking, checking, splitting and warping. Use RainCoat One Coat Clear Sealer to beautify and protect decks, porches, fences, shake, shingle and clapboard siding, boat decks, boardwalks, outdoor furniture, gazebos, arbors and trellises, storage sheds and more.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of the product

  • One coat application.
  • NeverWet® Properties Inside.
  • Superior water repellency.
  • Ready for use in 48 hours.
  • Mildew resistant coating.
  • Coverage: up to 250 sq ft per gallon with one coat.

How to Apply Wolman Water-Based RainCoat One Coat Clear Sealer

Surface Preparation

For best results, previous coatings such as paints, solid color and semi-transparent stains in a weathered state, should be stripped to create a bare, sound surface for maximum coating adhesion and durability. To remove oil, alkyd or latex, water base stains, use Wolman DeckStrip Stain & Finish Remover. For 100% acrylic solid or semi-solid stains, use Wolman DeckStrip ASR Acrylic Stain Remover.

For previous coatings in sound condition and for weathered transparent finishes, toners, and clear sealers, thoroughly clean with Wolman DeckBrite or Deck & Fence Brightener to remove chalky paint residue, embedded dirt, mildew and other contaminants, residual coating material and water repellents. According to label guidelines, select the appropriate cleaning product for your wood type, use according to directions and rinse with a power washer for best results. When dry, scrape off and sand any remaining loose flaking or peeling coating using 50 or 60 grit sandpaper. After wood is dry, conduct a splash test.


Based on 70°F (21°C) and 50% relative humidity. Dries the touch in 1 hour. APPLY ONLY ONE COAT. Allow to dry 24 hours before light foot traffic and 48 hour before replacing furniture or heavy foot traffic. If the surface is tacky or soft, extend the drying time before putting heavy objects back in place. Full cure to a hard finish will take approximately 7 days. Avoid dragging furniture across the surface. On newly sealed surfaces, allow 7 days for the coating to cure before washing.

Properties of Wolman Water-Based RainCoat One Coat Clear Sealer

Brand Wolman
Manufacturer Rust-Oleum
Resin Type Siloxane Modified Acrylic Copolymer
Pigment Type NA
Solvents Water, Glycol Ethers
Weight 3.78 Ltr.
Volatile Organic Compounds <250 g/l (2.08 lbs./gal.)
Recommended Dry Film
Thickness (DFT) Per Coat
1.0-1.5 mils
Wet Film to Achieve DFT
(unthinned material)
6.0-9.0 mils
Dry Times at 70-80°F
(21-27°C) and 50% RH
1 hour to Touch
24 hours to Light Traffic
48 hours to Replace Furniture
7 days to Full Care
Shelf Life 3 years
Flash Point >200°F (93°C)
Safety Information For additional information, see MSDS
Technical Data Sheet Click here