Rust-Oleum Tub and Tile Paint (Refreshing Kit) | Bathroom Tile Paint
Product Code: 7860519
Have a question?
Rust-Oleum Tub and Tile Epoxy Paint is refreshing kit which delivers excellent bonding, durability, as well as color retention in high moisture areas. This paint is designed with high performance formula that gives tough hard protective coating which acts like porcelain or ceramic. This kit is suitable to use for surfaces such as ceramic tile, acrylic, cast iron, steel tubs, porcelain and more. Tub and tile spray paint is also available.
Features of Tub and Tile Epoxy Paint
NOTE: This is not recommended in continues water immersion like ponds, hot tubs, saunas.
Featured Video of Rust-Oleum Specialty Tub and Tile Epoxy Paint
How to Use Rust-Oleum Tub and Tile Epoxy Paint?
Approproate Conditions to Use
Use when temperature is between 50-90ºF (10-32ºC) and humidity is below 85% to ensure proper drying. Properly ventilate the area by opening windows or using fans.
Remove metal drains and hardware. Remove loose paint and rust with a wire brush or sandpaper. Repair chips and cracks with a patching compound similar to Liquid Steel. Remove any mildew with a solution of bleach and water and rinse thoroughly. Scrub dirty or stained surfaces with an abrasive cleaner like Comet. Rinse with fresh water and allow to thoroughly dry. Remove all caulk. Wipe area clean. Prepare surface with an abrasive pad and Lime-AWay, rinse and repeat if necessary. Sand entire surface with #400/#600 grit wet/dry sandpaper. Vacuum or rinse away any residue. Wipe surface with a tack cloth immediately before painting to remove dust.
Application of Paint
Thoroughly mix Part B to ensure any settled pigment is redispersed. Add Part A to Part B and mix thoroughly for 1 minute. Thin no more than 10% (3 ounces per 1-quart) with 100% isopropyl alcohol (not rubbing alcohol), acetone or xylene. If less than a full (1 quart) kit is needed, mix in a 4:1 ratio of base to activator in a separate container. Apply within 6 hours of mixing.
Brush: Use a fine quality, fine bristle varnish brush. Brush in one direction only for a smooth surface and feather the edges as you paint to avoid a hard line between painted areas. Avoid excessive brushing to ensure an even coat and smooth finish. Apply two coats, waiting at least 1 hour between coats. If necessary, a third coat may be applied the next day with a second kit.
Roller: Use a high quality, ¼” short nap roller made for kitchen or bath use. Apply two coats, waiting at least 1 hour between coats. Avoid excessive brushing to ensure an even coat and smooth finish. If necessary, a third coat may be applied the next day with a second kit. If desired, conventional HVLP or airless sprayer may also be used.
Properties of Rust-Oleum SpecialtyTub and Tile Epoxy Paint
|Resin Type||Epoxy Acrylic|
|Pigment Type||Titanium Dioxide|
|Solvents||Ethyl Benzene, Light Aromatic Naphtha, Propylene
Glycol Monomethyl Ether, 1,2,4-Trimethylbenzene,
1,3,5 Trimethylbnezene, Xylene
|Recommended Dry Film Thickness
(DFT) per Coat
|1.5-2.0 mils (37.5-50µ)|
|Practical Coverage at Recommended
DFT (assumes 15% material loss)
|2 coats covers 70-110 sq.ft./quart|
|Dry Times at 70-80°F (21-27°C)
and 50% Relative Humidity
|1 hour to touch, 1-2 hours to re-coat, fully cure in 3 days.|
|Dry Heat Resistance||NA|
|Shelf Life||3 years|
|Flash Point||78°F (26°C)|
|Safety Information||For additional information, see MSDS|
|Technical Data Sheet||Click here|