248656 248656 Automotive

Rust-Oleum Automotive Professional Rubber Coating Spray

Product Code: 248656

Availability:Out of stock

Rs. 1,140.00 Rs. 1,026.00 1,026.00

Rust-Oleum Professional Rubber Coating Spray is an easy to use, black rubberized protective coating. It provides corrosion protection from water, salt and other chemicals. It helps deaden sound and prides a barrier from rust on cars, trucks, trailers and other recreational vehicles. For use on bare or primed metal including underbody and wheel wells of cars, trucks, trailers and other recreational vehicles. Not for use on surfaces that will come in direct contact with heat or high temperatures such as mufflers, exhaust components, etc. Professional Undercoating features an advanced spray system that allows you to spray at any angle, even upside down for those hard to reach areas. A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Rubber Coating Spray

  • Professional Grade.
  • Corrosion Resistant.
  • Deadens Sound.
  • Rubberized.
  • Paintable/Quick Dry.

NOTE: Hold can 12-16" from surface and spray in a steady back and forth motion, slightly overlapping each stroke. For best results, apply two coats.

Featured Video of Rubber Coating Spray

How to Apply Rubber Coating Spray?

Ideal Environmental Conditions

Use outdoors or in a well-ventilated area such as an open garage. Apply when temperature is between 50-90°F (10- 32°C) and humidity is below 85% to ensure proper drying. Avoid spraying in very windy, dusty conditions. Cover surrounding area to protect from spray mist.

Surface Preparation

Bare Metal or Sound Rust Surfaces: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or 120-220 grit sandpaper. Remove all sanding dust with a clean cloth. Protect and mask off all surrounding areas to prevent overspray. For best results, spot prime bare or rusted surfaces.

Previously Painted Surfaces: Thoroughly clean the area with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Note: Cleaning is recommended before and after wire brushing or sanding. Use a wire brush to remove any loose or peeling paint. Sand the surface with 120-220 grit sandpaper. The use of 249321 Primer Sealer Spray or any of the sandable primers (249419 Red, 252472 Light Gray, or 249415 Gray) will enhance corrosion resistance and improve hiding.


Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 12-16" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can in motion while spraying. Remove any overspray from the auto finish immediately. For best results, apply 2 coats, allowing 1-2 minutes between coats. Do not use near open flame.

Properties of Rubber Coating Spray

Brand Rust-Oleum
Weight 425 Grams
Recommended Dry Film
Thickness (DFT) per Coat
1.0-1.5 mils (25-37.5µ)
Practical Coverage at Recommended
DFT (assumes 15% material loss)
10-15 sq.ft./can
Dry Times at 70-80°F
(21-27°C) and 50% Relative Humidity
1 hour minutes to touch, re-coat in within 1 or after 24 hours
and 72 hours to fully dry
Resin Type Modified Alkyd
Pigment Type Carbon Black
Solvents Aromatic Hydrocarbons and Ketones
MIR 1.00 Max
Dry Heat Resistance 200°F (93°C)
Flash Point -156°F (-104°C)
Safety Information For additional information, see MSDS
Technical Data Sheet Click here